Member II
Looks like your not having fun! Time for a cold one[emoji482][emoji482][emoji482]
-
Guest, UPDATE We went through the site migration runbook and completed all steps. We will need to complete the migration next week, but will leave the forums up for the weekend. A few days after maintenance, a major upgrade revision to the forum site will occur.
-
Refurbishing a cheap Disco 1
- Thread starter systemdelete
- Start date
Pathfinder I
Several cold ones enjoyed last weekend, though I’m on call this week so an import Pepsi as a reward had to suffice.
On to today, the steering joints showed up and I pulled the steering linkages and began to replace them. My adjustment sleeve was frozen so I’ve given it a heavy dose of kroil and set it in the corner to have some time alone to think about what it’s done. I pressed the rest of the bushings out of the radius arms, and got the new ones all in place. They are back on the truck, so now it’s on to the steering linkages after lunch. . .
On to today, the steering joints showed up and I pulled the steering linkages and began to replace them. My adjustment sleeve was frozen so I’ve given it a heavy dose of kroil and set it in the corner to have some time alone to think about what it’s done. I pressed the rest of the bushings out of the radius arms, and got the new ones all in place. They are back on the truck, so now it’s on to the steering linkages after lunch. . .
Member III
Attachments won't open.
Pathfinder I
Got the truck aligned within spec, and greased the driveshaft’s slip joints and u-joints. Also rebled the brakes while on stands so I could replace a frozen bleed screw. . . Found so extra inspection holes in my passenger front rotor!
Pathfinder I
Reposted, tapatalk having issues apparently. :/
Member III
Pics came through fine, thank you. That hole looks like rock damage or someone hit it with a hammer. Cast iron does break. Your rigs looking just fine.
Got the truck aligned within spec, and greased the driveshaft’s slip joints and u-joints. Also rebled the brakes while on stands so I could replace a frozen bleed screw. . . Found so extra inspection holes in my passenger front rotor!
View attachment 119607View attachment 119606
Pathfinder I
Been busy with work the last couple evenings, cut short my time to work on the truck in the mornings when it’s cool outside.
I did get the front shock bushings replaced, no clue whether these started out as soft as butyl or whether some chemical/heat exposure turned them that way.
I did get the front shock bushings replaced, no clue whether these started out as soft as butyl or whether some chemical/heat exposure turned them that way.
Advocate I
Pathfinder I
No, typically they have been used for winter travel and the frames are less than stellar, if not rusted through. This one was a Texas truck before it was brought to TN in 2009. It is extremely rust free compared to most I’ve seen/worked on.
Pathfinder I
Was out today buying some feed, and noticed 1/2” rubber stall mats were on sale. . .
Having pulled the rotting soggy foam carpet under mat and factory carpet out of the back I wasn’t happy with the possibility of damaging the steel rear floorpan. I wasn’t enthused about rhino lining it as I have with previous trucks b/c it’s far cleaner and rust free than most. The rubber mats do a fine job of dampening the resonance of the large panel, while protecting it from the sorts of things I often toss in the back of my truck. And they are easy enough to remove for the occasional cleaning. Also they were budget friendly at around $75 for two of the mats and a blade for my vibratory tool to quickly cut them to shape.
Having pulled the rotting soggy foam carpet under mat and factory carpet out of the back I wasn’t happy with the possibility of damaging the steel rear floorpan. I wasn’t enthused about rhino lining it as I have with previous trucks b/c it’s far cleaner and rust free than most. The rubber mats do a fine job of dampening the resonance of the large panel, while protecting it from the sorts of things I often toss in the back of my truck. And they are easy enough to remove for the occasional cleaning. Also they were budget friendly at around $75 for two of the mats and a blade for my vibratory tool to quickly cut them to shape.
Member II
Wow! That looks great
Pathfinder I
lol thanks! I found myself oohing and aahing over your cup holders earlier, still need to get a set of those to put in.
Member II
Ebay find [emoji16] I've only had them for a few months but wow they are so awesome
Off-Road Ranger I
I may have a repair manual of some kind for this truck, is it worth my time to look for it? (would you be interested in it?)
I probably also have and engine ECU but I'm not sure about parts interchange.
Again, if you're interested, I'll dig them up, I'd like to get them out of the garage.
I probably also have and engine ECU but I'm not sure about parts interchange.
Again, if you're interested, I'll dig them up, I'd like to get them out of the garage.
Pathfinder I
I would certainly appreciate a FSM or similar in analog format. I have the .pdf but there’s something about having a manual in the shop when an engine is on the stand for a rebuild.
Off-Road Ranger I
I'll look at it and tell you what I have, maybe you can tell from that if it applies to your truck. There were not many changes in those years, until there were A LOT of changes! I'll get back to you.
Pathfinder I
Just finished pumping fresh 85w-140 into both diffs and the transfer case. While that was going on I rebuilt the vacuum lines to the cruise control and the brake pedal. Also found time to install the metric threads for my rear ladder since I didn’t want to use the huge sheet metal screws that were included with it.
Member III
QUESTION, what does a Toyota LC have in common with land Rover Disco ? Did you once own Land Rover Disco and have the old manuals for it ?
Advocate I
Yeah, that was my point. Most old LRs are prone to lots of rust... but yours seems very clean. That's why the rotor surprised me so much!
-TJ
