What Did You Do With Your Rig Today?

[DaleRF]

Yesterday I finished up most of the engine accessories on the CJ2, oil filter cannister, alternator, intake/exhuast, carb, fuel pump, oil feed and return lines for the oil filter assembly, distributor along with a Pertronix electronic drop in ignition, then got most of the clutch linkage assembled except I forgot to order the "adjustment yoke", so I put an order in for that along with a few other odds and ends. Hopefully tomorrow I can get the exhaust dropped in and welded up. Getting really close to time to put the tub back on. And I still need to order up new drive shafts.

That's going to be awesome...I mean, it already is!

 

[roots66]

Drove it to the office for the first time in over two years so I can telework from a cubicle instead of my house.

 

[orange01z28]

Got 37s

 

[DaleRF]

Got 37s

View attachment 234427

They look Great, as well as those wheels!

 

[El-Dracho]

Got 37s

View attachment 234427

Wow, looks great.

 

[PCO6]

I installed a hitch mounted tire carrier that I made for my Jeep XJ. I still have to complete the fold down table for it and change out a bit of hardware but it's mostly complete and it's functional.

 

[DaleRF]

I installed a hitch mounted tire carrier that I made for my Jeep XJ. I still have to complete the fold down table for it and change out a bit of hardware but it's mostly complete and it's functional.

View attachment 234441View attachment 234442

Nice!

 

[Michael]

I installed a hitch mounted tire carrier that I made for my Jeep XJ. I still have to complete the fold down table for it and change out a bit of hardware but it's mostly complete and it's functional.

View attachment 234441View attachment 234442

Great work!

 

[El-Dracho]

I installed a hitch mounted tire carrier that I made for my Jeep XJ. I still have to complete the fold down table for it and change out a bit of hardware but it's mostly complete and it's functional.

View attachment 234441View attachment 234442

That looks very good. Great work! That is a awesome XJ. Enjoy your travels with it.

 

[PCO6]

Thanks guys. I haven't had a chance to test it on a trail yet but I think I've hit every pot hole in town (on purpose) and so far so good. It's solid!

 

[Sparksalot]

Recovery hooks and deer armor.

 

[Staticline40]

Got rid of the silly suction cup mount for the display thingy using 67 Designs pieces parts

Silly suction cup mount



More gooder 67 Designs mount

 

[Jim SoG]

Got rid of the silly suction cup mount for the display thingy using 67 Designs pieces parts

Silly suction cup mount

View attachment 234482

More gooder 67 Designs mount

View attachment 234483

View attachment 234484

What mount is that Piece that bolts to the hand grab, Got a link? Sure looks great!

 

[Staticline40]

What mount is that Piece that bolts to the hand grab, Got a link? Sure looks great!

It's from 67 Designs for the FJ and Tacoma...

A Pillar Mount

 

[Stump Jumper]

Finished installing sPOD in my JKU.
Installation was fairly easy and it allowed me to clean up the wiring mess in the engine bay.
The toughest part was getting the ethernet cable up through and out of the A pillar to the location I wanted to mount the touch screen.
The screen mount is from 67 Design.

 

[05EXCURSION]

Got my battery mounted and plumbing figured out for the hot water heater and pump

 

[Staticline40]

Finally installed the Redarc solar system in the truck

 

[DaleRF]

Finally installed the Redarc solar system in the truck

Sweet!

 

[Ken M]

I pulled off the interior trim panels on the jeep to hide the wires for the air compressor that is mounted behind the rear seat.

 

[El-Dracho]

Got rid of the silly suction cup mount for the display thingy using 67 Designs pieces parts

Silly suction cup mount

View attachment 234482

More gooder 67 Designs mount

View attachment 234483

View attachment 234484

Great. Much better than these suction cup mounts!