Oh, and this spring I plan to remove the windguard, strip it down, repaint it, and have a "overlandbound.com" vinyl decal on the way for it.
What Did You Do With Your Rig Today?
- Thread starter iamout
- Start date
Off-Road Ranger I
- 2,771
- First Name
- David
- Last Name
- Goodyear
- Member #
0691
- Ham/GMRS Callsign
- KL7JKC
When I first met my wife, she had a "74" Opel Manta that the hinge pins were toast on the drivers door. I did many a "Duke's of Hazard" exit on that door. Man I miss that car...
Member III
Mounted some 37" KO2's on my JK, cause I couldn't get it done yesterday :)
Member II
Installed the first of 2 vertical Rotopax on the Wilco Hitchgate MAX. 2nd pack and universal mount arrive next week.
Built these for the back of the JKUR. Just need a coat of paint and another drawer slide.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Off-Road Ranger I
Wilco Offroad Hitchgate Max installed. Doing my own 4 gallon Rotopax mount, and may even stack 2 packs. Nice bonus - rear glass opens/clears without opening the carrier.
Very happy with this solid setup.
This is perfect! I've got a Jeep WK also and I've been semi-looking around, but now I'm sold. Thanks for sharing!
Pathfinder III
It is the simplest thing but still feels good to get it done. Oil Change.[emoji12]
Sent from my XT1650 using OB Talk mobile app
Sent from my XT1650 using OB Talk mobile app
Trying to get ready for a beach trip in two weeks... added a leaf to the rear, working on a tire carrier out of scrap metal from work, building some custom leaf spring mounts on the front to lift the front up a tiny bit more and change my pinion angle so my driveshaft will fit and my steering will be correct.
Sent from my iPhone using OB Talk
Sent from my iPhone using OB Talk
Primed and applied the first coat on my bare steel Hep's rack for my Xterra (and took a terrible picture to share):
I had pulled my Cobra 75-WX-ST out of my FJ Cruiser and finally finished the install in my 2016 4Runner. Had the antenna mounted and ran cable, had a sweet match when put on the meter, but hadn't done the finish work in the center console. Was struggling with the location. Completely done and super happy with it all.
Sent from my iPhone using OB Talk
Sent from my iPhone using OB Talk
Damn broken drill bit kept me from finishing the front suspension. But at least my spare tire carrier is 90% finished (need to relocate my license plate/run wiring for lights). Gotta wake up real early and put my front end back together before bossman gets to work in the morning lol
Sent from my iPhone using OB Talk
Sent from my iPhone using OB Talk
Traveler III
What did I do with my rig today? I used it as a tree substitute!
It was 68° yesterday, and 61° today in northern Ohio, where the average high for today is 38°. Yesterday broke the record by almost 10°. Normally this picture would have snow piled up at least as high as the ends of the hammock!
It was 68° yesterday, and 61° today in northern Ohio, where the average high for today is 38°. Yesterday broke the record by almost 10°. Normally this picture would have snow piled up at least as high as the ends of the hammock!
I finished the fab and install of my rocker switch panel. Need to build and run the wire harness down the a-pillar and into the engine compartment. I had never worked with Fiberglass before this project and it took me quite a while with a ton of sanding to get it completed but I think it turned out great. What do you guys think?
Traveler III
- 1,387
- First Name
- Mike
- Last Name
- Johnson
- Member #
3587
you could make that work I am sure.. I am not sure of the measurements but You might be able to just cut the center out and put switches in there. That is perfect already.
That looks great. I've been thinking of how to do something similar using the panel and wiring I already have in place for old Lexus Link stuff in my GX470.
Sent from my iPhone using OB Talk[/QUOTE
