Expedition Master I
- 5,314
- First Name
- joseph
- Last Name
- johnson
- Member #
-
16838
- Service Branch
- US ARMY
What Did You Do With Your Rig Today?
- Thread starter iamout
- Start date
Finally got around to some general maintenance. Adjusted the valves, gapped my spark plugs and points, set the timing and bled my clutch. She still runs like a champ. Plan on going out for some fun this weekend
Traveler II
Finally got my CB mounted. Now it doesn't have to sit under the seat all the time. Now it's time for a better antenna mounting system...
Got up early and decided to start the rear bumper project. No more fangs! [emoji4]
Pathfinder I
I finally got around to extending the wire harness for my hood mounted ditch lights. The harness wasn't long enough to tuck under the cowl and reach the passenger side light. I had it run against the firewall and ziptied to the AC lines which looked janky. I didn't wire loom or heat shrink large enought to fit 2 14ga wires so I twisted them together like we used to do for complicated car alarm installs. It came out nice and clean although you'll never see it under the cowl. :)
Before
After
I decided to mount the Arkon tablet arm to the transmission tunnel. I didn't feel like modifying the passenger seat bracket to try and make a mount. Once I get the bar shaped the way I want I will try to stiffen it up by adding another length of metal inside the loom and then pin it to point higher up on the console with a clamp. It's currently very sturdy but the tablet wobbles a lot if that make sense.
Before
After
I decided to mount the Arkon tablet arm to the transmission tunnel. I didn't feel like modifying the passenger seat bracket to try and make a mount. Once I get the bar shaped the way I want I will try to stiffen it up by adding another length of metal inside the loom and then pin it to point higher up on the console with a clamp. It's currently very sturdy but the tablet wobbles a lot if that make sense.
Enthusiast III
- 2,421
- First Name
- Joseph
- Last Name
- Arietta
- Ham/GMRS Callsign
- KMA6AIU
- Service Branch
- US Submarine Force
plugs and wires and a good cleaning today. Plus Im gonna figure out a bin that I like to keep my everyday gear in the bed. Ill post a couple pics later
Enthusiast III
Roof rack and lights added to Grover the Rover
Traveler II
Traveler III
Picked up a small shovel, hi-lift jack base and a shovel/axe mount. Mount is Smittybilt so it bolted right up to the Smittybilt basket, with some slight trimming of the brackets. Picked up some stainless hardware and mounted the base to the basket as well.
Enthusiast III
Several mods to my 2004 TJ Rubicon this weekend:
Poison Spyder hood louver
Teraflex sway bar quick disconnects
Daystar hood latches
Poison Spyder hood louver
Teraflex sway bar quick disconnects
Daystar hood latches
Attachments
Member II
.... New to it, a mildly built 4.6l [emoji67][emoji373][emoji67][emoji373]. Oh and hello to everyone. I'm new
Member III
I changed my tire after blowing it out romping through the hills near my place. I did a bit more damage than I initially thought... totally worth it though! 
Member III
Says I don't have permission to edit my post... this picture didn't go through so I'll try to add it as a reply. Here goes.
Attachments
Enthusiast III
Nice job! Definitely proof that you had fun..hell yeah!!
Traveler II
Hey! Welcome and great looking Disco you've got there!
Welcome ..... Not gonna lie when I say I don't miss taking one of those engines apart LOL
Expedition Master I
- 11,455
- First Name
- Michael
- Last Name
- Lee
- Member #
-
13728
- Ham/GMRS Callsign
- KM6YKV
- Service Branch
- Army & Marine Corps
Got little signal, here what we’re doing with our rigs! Mojave road
