2016 Toyota Tundra Multi Phase Build
- Thread starter CFTAdventures
- Start date
Added King Shocks all around. After adding the 4 inch lift, measured and sent specifics to King Racing and they built one off shocks that fit like a glove and the wife sez the ride is even better than Toyota factory.
Nice ride!
Exterior:
A.R.E CX HD Series Truck Cap
Warrior Roof Rack
TRD PRO Front Bumper
Color Matched Hood Bulge
Color Matched Bumper End Caps and Lower Valence
Color Matched Mirror Caps and Door Handles
LUND Fender Flares
N-Fab Nerf Bar
RC Bull Bar
RCI Full Under Body skid plates
Recovery:
Front and Rear ARB Air Lockers
Max traxx
ARB Air jack
High lift
Suspension:
BDS 7" Lift Kit
7" Fox 2.5 Coil Overs with Piggy back reservoir
Icon upper control Arms
Icon 2.5 piggy back shocks w/ CDC
Dakar Leaf Pack w/ add a leaf
Boss Triple Bag air suspension
Wheels and Tires:
Fuel Anza 18x9 in Gun Metal
Nitto Ridge Grapplers 37x12.5R18
Lighting:
Rigid Fog Light kit w/ mounting kit
30" RC Light bar in the lower Valence
40" RC Light bar in Hood Bulge/ SDHQ mounting kit
50" RC Light Bar on Roof Rack
6 x 8" RC Perimeter Lights
8 x 2" RC rock lights
2 x 4" RC reverse lights in Rear Bumper
12" Light bar inside Truck Cap
Communication:
Midland MXT 115 GRMS Radio
Cobra CB Radio
Delorme Explorer GPS
Ipad w/ Garmin and Hema Maps
Engine/performance and Electrical:
4.88 Nitro Gears
K&N Cold Air Intake
EBC heavy duty brake pads and drilled and slotted rotors
Hyper tech speedometer chip
Flowmaster Outlaw Exhaust
National Luna Dual Battery Solenoid
National Lune Dual Battery Controller
3 x Interstate 110 Amp Hour Batteries
NOCO Genius Battery Charger
Blue Sea 12 Fuse Block
2 x 50 Amp Circuit Breaker
6x Blue Sea USB Ports
3x Blue Sea 12 volt ports
Switch Panel
1000 watt Inverter
Camping and Storage:
CVT MT Shasta Tent
Go Rhino Foxing Awning
DECKED Storage system
ESP Under Seat Storage
Dometic 55L Fridge/Freezer
Dometic Fridge Slide
Front Runner 17.7 Water Tank
SURFLO Water Pump
So I am pretty late in putting this Build Thread together but better late then never! Bought a 2016 Toyota Tundra 1794 4x4 in November 30 2015, stayed stock for about 5 days before adding the first round of modifications.
View attachment 31264
First up was a BDS 3/2 leveling Kit, Lund Fender flares, Fuel Anza 18x9, Falken Wildpeak 35x12.5, Rhino nerf bar, LED Interior and Exterior Light Conversion, K&N Cold Air Intake, Flow Master Outlaw Exhaust.
View attachment 31273
Truck Sat like this for about 5 months before I decided to upgrade the suspension. I went with a BDS 4 1/2 Coil Overs up front and Fox 2.0 Rear Shocks. Also aded in a set of Dakar Leaf Spring pack. I had to start getting rid of the chrome so we went with the TRD Pro Front Grill , Color Matched Hood Bulge , Color Matched Door Handles and Mirror Caps. Decided to put in a 40" light bar in the Hood Bulge as well as a 30" light bar in the lower bumper cover. Bull Bar went on as well.
View attachment 31274
View attachment 31275
We have a 2015 4 Runner Limited and the one main difference between these two vehicles stock is the JBL in the 4Runner is amazing and the one in the Tundra is a Joke. So I sucked it up and dropped in a custom sound system with 2 x 10's behind the seat, Also added in a ARB air Compressor , ARB Diff Breathers, a Rear third brake light and some additional reverse lights.
View attachment 31276
View attachment 31277
Truck sat with this set up for about 6 months before we decided we wanted to clean up the front end a bit
( with 35's we had to trim the front fender and remove the inner fender panel, replaced everything!) So we decided to go with a 7" Fox 2.5 coil over in the front and a Icon 2.5 Piggy Back CDC in the rear,. We also added in a leaf to help with the weight of the RTT and Camping gear (using the front runner load bars). We also threw on a new set of Nitto Ridge Grapplers 35x12.5 .We also decided to get a color matched lower bumper valance as well as color matched bumper end caps and put in a CB Radio ( and PA cause its fun).
View attachment 31284
View attachment 31286
Truck Sat this way for about 5 months until our most recent round of modifications. We wanted to take the next step into the "overland" build and decided to really sit down and plan out what would make our lives more convenient while out on the trail and while camping.
Started with the cargo management, We decided to go with a A.R.E CX Series HD Cap (Includes interior cage 800lb moving limit) , a Decked Draw system and a ESP under seat storage. These modifications alone were Amazing , Everything was organized and had its place! ( My wife says I am a little OCD ).
View attachment 31288
View attachment 31290
Next was Power Management , We are running the National Luna Dual Battery System on the truck but for the house battery we have two 110 Amp hour batteries running parallel. This is powering our Control panel which houses Our light switches , 8 x USB ports, 4x 12 Volt Ports, the Fridge, water pump and a 1000 watt inverter.
I wanted to split the inverter so we are running two set ups one power wire going to a circuit breaker then to a fuse block then to the inverter. The other power wire is going to a circuit breaker , fuse block then the switch panel. We are also running a drip charger so that the night before a trip I can top off the batteries before we hit the road, also nice to be able to plug in on the road as well.
View attachment 31291
We also tackled the water system at the same time, we installed a 17.7 gallon water tank from front runner being run by a Sureflo Water pump. We have it terminated with a shower head which has come in handy for washing off. You can also see where we mounted our Maxtrax's!
View attachment 31293
The next step was the roof rack, This is the one aspect I spent less then I should of , we went with a Warrior rack and I should have gone with a front runner. It would of made mounting the accessories so much easier! On the rack we have our CVT Mt Shasta Tent as well as a Rhino Fox wing awning. Maybe its just me but I love LED lights so we decided to put a few more lights on the truck! We went with 6 x 8" LED lights as Perimeter lights as well as 8 Rock lights. These Rock lights are great for camping! It provides ample light and is down low so it does not bother everyone at camp. I also added on a 50" light bar as well.......
View attachment 31295
View attachment 31296
View attachment 31297
Lastly we have our Navigation and Communication, We are currently running a Midland MXT 115 Radio , Cobra CB Radio ,Delorme Explorer GPS and our iPad for Maps. iPad is mounted with a RAM Mount and its working our great for us!
View attachment 31298
View attachment 31300
We have only gotten out on a couple trips with the current set up and love it! Already have plans for the next phase! Picture out on SkyLine Drive on our most recent trip!
View attachment 31303
Here is a list of things to come!
4.88 Gears!! ( This is a must with the added weight!)
Front and Rear ARB Air Lockers
White Knuckle Sliders
RCI Trans and Fuel Tank skid plates
The Rear is sagging about 1 1/2 over the front when fully loaded, I can't add Shackles because it will hit the exhaust, I don't want to add blocks because of the axle wrap.....which leaves me with the potential of putting on a custom set of Air Bags...We will see.
Ill keep updating as the mods go on![/QUOTE]
Exterior:
A.R.E CX HD Series Truck Cap
Warrior Roof Rack
TRD PRO Front Bumper
Color Matched Hood Bulge
Color Matched Bumper End Caps and Lower Valence
Color Matched Mirror Caps and Door Handles
LUND Fender Flares
N-Fab Nerf Bar
RC Bull Bar
RCI Full Under Body skid plates
Recovery:
Front and Rear ARB Air Lockers
Max traxx
ARB Air jack
High lift
Suspension:
BDS 7" Lift Kit
7" Fox 2.5 Coil Overs with Piggy back reservoir
Icon upper control Arms
Icon 2.5 piggy back shocks w/ CDC
Dakar Leaf Pack w/ add a leaf
Boss Triple Bag air suspension
Wheels and Tires:
Fuel Anza 18x9 in Gun Metal
Nitto Ridge Grapplers 37x12.5R18
Lighting:
Rigid Fog Light kit w/ mounting kit
30" RC Light bar in the lower Valence
40" RC Light bar in Hood Bulge/ SDHQ mounting kit
50" RC Light Bar on Roof Rack
6 x 8" RC Perimeter Lights
8 x 2" RC rock lights
2 x 4" RC reverse lights in Rear Bumper
12" Light bar inside Truck Cap
Communication:
Midland MXT 115 GRMS Radio
Cobra CB Radio
Delorme Explorer GPS
Ipad w/ Garmin and Hema Maps
Engine/performance and Electrical:
4.88 Nitro Gears
K&N Cold Air Intake
EBC heavy duty brake pads and drilled and slotted rotors
Hyper tech speedometer chip
Flowmaster Outlaw Exhaust
National Luna Dual Battery Solenoid
National Lune Dual Battery Controller
3 x Interstate 110 Amp Hour Batteries
NOCO Genius Battery Charger
Blue Sea 12 Fuse Block
2 x 50 Amp Circuit Breaker
6x Blue Sea USB Ports
3x Blue Sea 12 volt ports
Switch Panel
1000 watt Inverter
Camping and Storage:
CVT MT Shasta Tent
Go Rhino Foxing Awning
DECKED Storage system
ESP Under Seat Storage
Dometic 55L Fridge/Freezer
Dometic Fridge Slide
Front Runner 17.7 Water Tank
SURFLO Water Pump
So I am pretty late in putting this Build Thread together but better late then never! Bought a 2016 Toyota Tundra 1794 4x4 in November 30 2015, stayed stock for about 5 days before adding the first round of modifications.
View attachment 31264
First up was a BDS 3/2 leveling Kit, Lund Fender flares, Fuel Anza 18x9, Falken Wildpeak 35x12.5, Rhino nerf bar, LED Interior and Exterior Light Conversion, K&N Cold Air Intake, Flow Master Outlaw Exhaust.
View attachment 31273
Truck Sat like this for about 5 months before I decided to upgrade the suspension. I went with a BDS 4 1/2 Coil Overs up front and Fox 2.0 Rear Shocks. Also aded in a set of Dakar Leaf Spring pack. I had to start getting rid of the chrome so we went with the TRD Pro Front Grill , Color Matched Hood Bulge , Color Matched Door Handles and Mirror Caps. Decided to put in a 40" light bar in the Hood Bulge as well as a 30" light bar in the lower bumper cover. Bull Bar went on as well.
View attachment 31274
View attachment 31275
We have a 2015 4 Runner Limited and the one main difference between these two vehicles stock is the JBL in the 4Runner is amazing and the one in the Tundra is a Joke. So I sucked it up and dropped in a custom sound system with 2 x 10's behind the seat, Also added in a ARB air Compressor , ARB Diff Breathers, a Rear third brake light and some additional reverse lights.
View attachment 31276
View attachment 31277
Truck sat with this set up for about 6 months before we decided we wanted to clean up the front end a bit
( with 35's we had to trim the front fender and remove the inner fender panel, replaced everything!) So we decided to go with a 7" Fox 2.5 coil over in the front and a Icon 2.5 Piggy Back CDC in the rear,. We also added in a leaf to help with the weight of the RTT and Camping gear (using the front runner load bars). We also threw on a new set of Nitto Ridge Grapplers 35x12.5 .We also decided to get a color matched lower bumper valance as well as color matched bumper end caps and put in a CB Radio ( and PA cause its fun).
View attachment 31284
View attachment 31286
Truck Sat this way for about 5 months until our most recent round of modifications. We wanted to take the next step into the "overland" build and decided to really sit down and plan out what would make our lives more convenient while out on the trail and while camping.
Started with the cargo management, We decided to go with a A.R.E CX Series HD Cap (Includes interior cage 800lb moving limit) , a Decked Draw system and a ESP under seat storage. These modifications alone were Amazing , Everything was organized and had its place! ( My wife says I am a little OCD ).
View attachment 31288
View attachment 31290
Next was Power Management , We are running the National Luna Dual Battery System on the truck but for the house battery we have two 110 Amp hour batteries running parallel. This is powering our Control panel which houses Our light switches , 8 x USB ports, 4x 12 Volt Ports, the Fridge, water pump and a 1000 watt inverter.
I wanted to split the inverter so we are running two set ups one power wire going to a circuit breaker then to a fuse block then to the inverter. The other power wire is going to a circuit breaker , fuse block then the switch panel. We are also running a drip charger so that the night before a trip I can top off the batteries before we hit the road, also nice to be able to plug in on the road as well.
View attachment 31291
We also tackled the water system at the same time, we installed a 17.7 gallon water tank from front runner being run by a Sureflo Water pump. We have it terminated with a shower head which has come in handy for washing off. You can also see where we mounted our Maxtrax's!
View attachment 31293
The next step was the roof rack, This is the one aspect I spent less then I should of , we went with a Warrior rack and I should have gone with a front runner. It would of made mounting the accessories so much easier! On the rack we have our CVT Mt Shasta Tent as well as a Rhino Fox wing awning. Maybe its just me but I love LED lights so we decided to put a few more lights on the truck! We went with 6 x 8" LED lights as Perimeter lights as well as 8 Rock lights. These Rock lights are great for camping! It provides ample light and is down low so it does not bother everyone at camp. I also added on a 50" light bar as well.......
View attachment 31295
View attachment 31296
View attachment 31297
Lastly we have our Navigation and Communication, We are currently running a Midland MXT 115 Radio , Cobra CB Radio ,Delorme Explorer GPS and our iPad for Maps. iPad is mounted with a RAM Mount and its working our great for us!
View attachment 31298
View attachment 31300
We have only gotten out on a couple trips with the current set up and love it! Already have plans for the next phase! Picture out on SkyLine Drive on our most recent trip!
View attachment 31303
Here is a list of things to come!
4.88 Gears!! ( This is a must with the added weight!)
Front and Rear ARB Air Lockers
White Knuckle Sliders
RCI Trans and Fuel Tank skid plates
The Rear is sagging about 1 1/2 over the front when fully loaded, I can't add Shackles because it will hit the exhaust, I don't want to add blocks because of the axle wrap.....which leaves me with the potential of putting on a custom set of Air Bags...We will see.
Ill keep updating as the mods go on![/QUOTE]
Enthusiast I
Slo4x4
Rank III
Enthusiast III
I love this, Leer cap? curious as to the height difference between the two racks? Are they perfectly level to each other or is one a bit lower? Just curious
getting ready for Mojave Road trip...B.O.B. is ready for another adventure!
Attachments
Off-Road Ranger I
This is a fantastic build. Strong work! Nice to see some more full size trucks getting on the trail.
This build came together quickly!! RIG looks great enjoy the trip! Can’t wait for winter to be over to get back out there lol
tundra21
Rank V
Advocate III
Impressive Build, I may copy some of your ideas. I had no idea Truck caps would hold up to the punishment of Off Road so now back on my list.
We did go with the HD Cap to get the built in cage. Static weight goes from 300lbs to 800lns.
Install Genesis Off Road Dual Battery system with sPod in my 2017 Tundra.
Genesis Off Road battery monitor and by pass to link batteries for emergency boost.
sPod touchscreen
Genesis Off Road battery monitor and by pass to link batteries for emergency boost.
sPod touchscreen
tundra21
Rank V
Advocate III
They did a great job with this kit. Nice install!
More changes the last few days. ARB Summit Bumper, Warn Platinum Zeon 10.5k and ARB Intensity Spot with an Intensity Combo on back order.
New Method Racing wheels and Nitto Ridge Grapplers going on next Thursday. Drop down slide out and fridge going in tomorrow. Leaving week from Sunday for 6 days of wheeling and surf fishing on the Outer Banks of NC. Also take the ferry over to Ocracoke and Portsmouth Islands.
New Method Racing wheels and Nitto Ridge Grapplers going on next Thursday. Drop down slide out and fridge going in tomorrow. Leaving week from Sunday for 6 days of wheeling and surf fishing on the Outer Banks of NC. Also take the ferry over to Ocracoke and Portsmouth Islands.
Is that a Wilco Tire Gate? If so, what do you think of it? If not, details would be appreciated.
