What Did You Do With Your Rig Today?
- Thread starter iamout
- Start date
Member III
- 2,771
- First Name
- Rolando
- Last Name
- Nispiros
- Member #
17011
- Ham/GMRS Callsign
- KN6JJS
Replaced fog light HIDs to LEDs. Thought I had a problem with the ballast. Got LEDs then Googled my problem. Turned out to be a popped fused so I pulled out HID fog kit for nothing. Oh well LED bulbs in amber still looks good just doesn’t have the power output (I think) of HIDs.
I like the L-track. I need to get some of that for my decked system. sucks not having easy tie down points when the decked system is in
Apoclapedia
Rank IV
Advocate I
I should be getting a new clutch delivered for my OBS F350 later today. New front fenders are on backorder and i moved my half ton crane on to it too.
The L tracks are great...tried to do mine on the cheap and bought 4-4' sections of an off-brand and found out the hard way that you have to buy the ones from Decked or the holes don't line up with cross braces under the deck (unless you want to drill and countersink all new holes). Tried to use the off-brand on the bed rails but they wouldn't stick out past the shell so I opted to install the uni-strut (c-channel) there.
good to know. I was thinking of ordering my own L-track, but now im second guessing it after reading your post. I'll most likely order the Decked Track instead.
Boostpowered
Rank VI
Member III
Member III
- 2,771
- First Name
- Rolando
- Last Name
- Nispiros
- Member #
17011
- Ham/GMRS Callsign
- KN6JJS
Replaced my older phone mount with a Qi wireless charger mount from Pro Clip. The previous mount was limiting how big a phone I could mount. Each year or couple years my phone has only gotten bigger/taller.
Also replaced my license plate holder attached to my Wilco hitch tire carrier. Didn’t like the LED bulbs/bolts I had previously. This has the LED light built into frame. Feels more solid of an install.
Also replaced my license plate holder attached to my Wilco hitch tire carrier. Didn’t like the LED bulbs/bolts I had previously. This has the LED light built into frame. Feels more solid of an install.
Quality of life improvements. Replaced cheap Walmart topper with the one off my bed. Tent barely closes with sleeping bags and pillows now, though it also barely closed before. Big thing I like about fiberglass RTTs: they can flex. Will be camping tonight to test it out
Influencer III
- 4,312
- First Name
- Rex
- Last Name
- Drake
- Member #
19540
- Ham/GMRS Callsign
- KI5GH
- Service Branch
- Air Force
Thecopcar got an awning. Theothertwin looks on in jealousy.
Apoclapedia
Rank IV
Advocate I
That looks cool. Where i live were not allowed to tint the front side windows. But that looks sharp. I like it.
Thanks! This window tint percentage is illegal here where I live near San Francisco, but I’ve had all my vehicles tinted without any hassle from law enforcement. This particular tint is 5% but legal tint allowed here is 70% on the front windows. If I do get pulled over it’s a “fix-it” ticket and a small fine.
Member III
- 2,827
- First Name
- Joshua
- Last Name
- Downs
- Member #
20468
- Ham/GMRS Callsign
- KK6RBI / WQYH678
- Service Branch
- USMC 03-16, FIRE/EMS
Installed a twin stick kit in the CJ5. JB Customs. Initially I only had 2wd, 4wd HI, 2wd Lo, but was locked out of 4 low. A call to their customer service people and they explained that on some of the short clocked twin stick shifters the factory mount would be slightly taller than others and the shifter channels would run out of travel before the interlock pills would clear for 4low. 20 minutes later I had it fixed after pulling the shifters and using the die grinder to elongate the channels a little bit. Threw it all back together and have a great slop free t-case shifter. The overly complex single stick linkage is waiting to go in the scrap pile.
Enthusiast III
- 3,335
- First Name
- Todd
- Last Name
- Beckley
- Member #
14953
- Ham/GMRS Callsign
- KC3THB
- Service Branch
- US Marine Corps
Put new rear rotors and brakes on the Jeep.
mface7
Rank V
Influencer II
counting the days until my incandescent bulbs burn out so I can change out to LEDs without feeling overly wasteful...
Member III
- 2,771
- First Name
- Rolando
- Last Name
- Nispiros
- Member #
17011
- Ham/GMRS Callsign
- KN6JJS
I'm very wasteful lol. I'm sure I already have some LED bulbs around, was just too lazy to find them.
mface7
Rank V
Influencer II
I probably would just not have been able to find them, bought new ones, installed them, and then found the ones I already had, then put those away somewhere "safe" so I'd remember, and then repeated the process a few years down the road.
Member III
- 2,771
- First Name
- Rolando
- Last Name
- Nispiros
- Member #
17011
- Ham/GMRS Callsign
- KN6JJS
Haha I too have many 'safe' places lol.
Trail Blazer II
- 6,140
- First Name
- Shaun
- Last Name
- Johannes
- Member #
15310
- Ham/GMRS Callsign
- KE8TDZ
Must be a common problem. I have the same one
