I lifted the Ramchager about 2 feet..... then I put it down. Actually I just used it to test the new hydraulic lift in my shop.
What Did You Do With Your Rig Today?
- Thread starter iamout
- Start date
Expedition Master III
- 5,643
- First Name
- Mac
- Last Name
- Raslan
- Member #
4788
- Ham/GMRS Callsign
- KJ7TLH or GMRS WRBM678
- Service Branch
- Sweet District II
Installed one inch blocks in the rear for added clearance, wish I would've done shackles. I'll probably eventually trade them for shackles at some point.
Sent from my SAMSUNG-SM-T337A using Tapatalk
Sent from my SAMSUNG-SM-T337A using Tapatalk
Member II
Offering some info:
I use a weBoost cell signal booster in my Jeep. Excellent product. Cell signal is pinned at full bars and 4G constantly. Saves battery as well, from less signal strength searching. Adding the trucker kit version to my camper next week.
Member II
Offering some info:
I use a weBoost cell signal booster in my Jeep. Excellent product. Cell signal is pinned at full bars and 4G constantly. Saves battery as well, from less signal strength searching. Adding the trucker kit version to my camper next week.
Off-Road Ranger I
Pathfinder I
Traveler III
- 1,387
- First Name
- Mike
- Last Name
- Johnson
- Member #
3587
Had the day off so I got a little dirty on some power line trails near home.
Continued tapping my foot, waiting on my winch bumper and sliders....
OB#3799
OB#3799
Traveler III
- 4,002
- First Name
- Kelly
- Last Name
- Herrin
- Member #
2032
- Ham/GMRS Callsign
- KFØDEX
Got my new tail lights installed ...
Plus, I received my Haynes Manual, and two copies of the 2017 Milepost for @Narbob and I to help plan our trip to Prudhoe Bay this summer...
Plus, I received my Haynes Manual, and two copies of the 2017 Milepost for @Narbob and I to help plan our trip to Prudhoe Bay this summer...
Last edited:
Member III
Prepping for camping this weekend. We're just going up to the local lake to spend a couple nights and test out the new tent. Hopefully this will get everyone ready for camping on the OBX this summer!
Advocate II
Raised my truck up into the air, spun it 180deg, then replaced my Driveshaft Support Bearing.
-CP TACO
OB #2376
-CP TACO
OB #2376
Finished my auxiliary fuse panel. Everything that works through this panel comes from the 2nd battery. All protected with a 150 amp fuse.
I will be using 2 of those relays for lights that I have now...I installed extra since I was there. I still have room to add 6 more circuits from that fuse panel. I will use 1 gauge wire from the batter to supply this panel..in case I want to add stuff later. Its in the place of my old glove box.
I will be using 2 of those relays for lights that I have now...I installed extra since I was there. I still have room to add 6 more circuits from that fuse panel. I will use 1 gauge wire from the batter to supply this panel..in case I want to add stuff later. Its in the place of my old glove box.
Pathfinder I
Pathfinder I
Nothing really just had a load of shiny stainless steel bolts, nuts and washers come to replace all the rusty bolts that I took off. SHINY
Traveler III
- 1,387
- First Name
- Mike
- Last Name
- Johnson
- Member #
3587
Traveler III
- 4,002
- First Name
- Kelly
- Last Name
- Herrin
- Member #
2032
- Ham/GMRS Callsign
- KFØDEX
Traveler III
- 4,002
- First Name
- Kelly
- Last Name
- Herrin
- Member #
2032
- Ham/GMRS Callsign
- KFØDEX
I have no idea why I waited 15 years to do this! :-) So easy! Special thanks to @Midsierracruiser for the use of the nibbler.
(14 min compressed down to 3 min)
(14 min compressed down to 3 min)
Last edited:
