Telescopic Awning 1.0

[CurrentlyRockhoundin]

A photo is worth a thousand words, so I a video is worth at least 1250 words.

So this is the first version of my telescopic awning and already I see changes and improvements I would like to make for the next one. Clearly welding vs hose clamps is going to happen but for testing this works fine.

The design considerations for my awning were as follows.
1. NO pvc pipe
2. Low profile
3. Affordable
4. Lightweight
5. Simple and sleek design
6. Replaceable tarp (sil, poly, or nylon) all work here
7. The ability to run a larger tarp simply by drilling one hole in the exterior tube.

I'm open to thoughts and constructive criticism since this is the first pancake.

 

[Tvot84]

That's pretty awesome! I love the simple/cheap ingenuity in that. I don't have any thoughts or criticism as of right now, but if I think of some, I'll be sure to let you know!

 

[persquank]

This is a great idea. Get some collapsible poles for the corners or just tie it to a near by tree.

 

[CurrentlyRockhoundin]

This is a great idea. Get some collapsible poles for the corners or just tie it to a near by tree.

Thanks.

I think the concept is sound, it just needs bugs worked out.

 

[PapaDave]

One additional design consideration for you is if you can nest one more smaller pole inside of your extending pole, then cut a square notch into the end of that middle size square tube, the smallest nesting pole can swing out on your locking pin as a hinge fitting snuggly into the middle tubes square notch at a right angle and give you hard sides to lash your tarp to. Make sense?

 

[Pyrotech]

where did you get the detent springs?

 

[CurrentlyRockhoundin]

One additional design consideration for you is if you can nest one more smaller pole inside of your extending pole, then cut a square notch into the end of that middle size square tube, the smallest nesting pole can swing out on your locking pin as a hinge fitting snuggly into the middle tubes square notch at a right angle and give you hard sides to lash your tarp to. Make sense?

I like that idea.

 

[CurrentlyRockhoundin]

where did you get the detent springs?

My local steel yard sells them but if you search Amazon for "Spring Clips" "Tent Pole Clips" or "Snap Button Clip" you will start to pull them up. Also Mcmaster Carr with likely have them as well.

 

[max.grun]

A photo is worth a thousand words, so I a video is worth at least 1250 words.

So this is the first version of my telescopic awning and already I see changes and improvements I would like to make for the next one. Clearly welding vs hose clamps is going to happen but for testing this works fine.

The design considerations for my awning were as follows.
1. NO pvc pipe
2. Low profile
3. Affordable
4. Lightweight
5. Simple and sleek design
6. Replaceable tarp (sil, poly, or nylon) all work here
7. The ability to run a larger tarp simply by drilling one hole in the exterior tube.

I'm open to thoughts and constructive criticism since this is the first pancake.

I really like this. Maybe you can braze/solder the brackets to the pipes if a welder is not available? I'm not sure though.

If you don't mind i may use a similar idea to setup a tarp on my rig. I like the Slumberjack tarp but necessarily want to run it over the back of the rig like i see so many others do.

 

[CurrentlyRockhoundin]

I really like this. Maybe you can braze/solder the brackets to the pipes if a welder is not available? I'm not sure though.

If you don't mind i may use a similar idea to setup a tarp on my rig. I like the Slumberjack tarp but necessarily want to run it over the back of the rig like i see so many others do.

I can weld aluminum, I just didn't for this first setup so I can take it apart and change thing around.

Do I would love to see some of photos of what you come up with when your done.

 

[Kardolf]

How about cutting some kind of "finger notch" on the ends of the larger exterior tube, to make it easier to grab the inner extension? Or, setting it up so the inside sticks out by 1" when the retention pin is in place?

 

[CurrentlyRockhoundin]

How about cutting some kind of "finger notch" on the ends of the larger exterior tube, to make it easier to grab the inner extension? Or, setting it up so the inside sticks out by 1" when the retention pin is in place?

I like that idea!

 

[RusD]

One additional design consideration for you is if you can nest one more smaller pole inside of your extending pole, then cut a square notch into the end of that middle size square tube, the smallest nesting pole can swing out on your locking pin as a hinge fitting snuggly into the middle tubes square notch at a right angle and give you hard sides to lash your tarp to. Make sense?

My ARB awning uses the side poles, but honestly I have wondered it they are really necessary. I highly recommend guying out the free end regardless of wind conditions; I've learned that lesson the hard way. With the tension in the guy lines and adjustable height legs, you don't have to have side supports.

I like the design, its looking good. I would like to know where you got the aluminum that fits inside so snugly. Everything at my local stores fit too loosely when I was working on legs for my kitchen setup.

 

[CurrentlyRockhoundin]

Thanks!

You can buy it online from my local metal supply.

Telescopic Tubing - Alcobra Metals

With a variety of shapes and sizes, telescopic tubing can help you make your product complete. Take a look at the many different solutions we offer.

alcobrametals.com

 

[RusD]

Thanks!

You can buy it online from my local metal supply.

Telescopic Tubing - Alcobra Metals

With a variety of shapes and sizes, telescopic tubing can help you make your product complete. Take a look at the many different solutions we offer.

alcobrametals.com

Awesome, thank you!

 

[M Rose]

I like your awning Jared, for cheap side protection you could get some nylon backpacking tarps from Walmart. They are super compact and light weight...

Robot or human?

I carry 4 of these to make awning shelters between my backpacking tents, and to make a lean-to against my rig

 

[Prerunner1982]

Well done. I like the telescoping mount.
I will be interested to see how it holds up.
I made a "Tactical Awning for Rain Protection"....aka T.A.R.P. using 10' of conduit (9' wide tarp) and the end that sticks out over the hood has started to bend as it's been through a couple of storms and high wind events.
The conduit is 3 sections so I will likely do away with that last section and just angle that end of the tarp down, tied off to the front of the Jeep.

 

[CurrentlyRockhoundin]

Well done. I like the telescoping mount.
I will be interested to see how it holds up.
I made a "Tactical Awning for Rain Protection"....aka T.A.R.P. using 10' of conduit (9' wide tarp) and the end that sticks out over the hood has started to bend as it's been through a couple of storms and high wind events.
The conduit is 3 sections so I will likely do away with that last section and just angle that end of the tarp down, tied off to the front of the Jeep.

So far it has held up very well. There's really nothing at all to break on it and from what I can tell it's far more simple and robust then anything else I have seen on the market so I'll be making a fully welded one soon as well.
T6 Aluminum square tube with a .110 wall is really strong.