Propane Bottle Mounts- Show Us Yours

[Wanderlost]

I need to switch over from disposable propane bottles to a semi-permanently mounted 5# -8" diameter or a 10# -8.9" diameter tank. Any advice on mounts? Our situation calls for it to be bolted to the top rail of our dual swing-out bumper, next to the tire. So the bolts will have to go down, through the bottom. So a good, thick, solid bottom is a must. We'll make a support bracket as well. We don't need anything fancy, just secure and durable, store-bought or homemade.
Any suggestions or photos of what your setup would be greatly appreciated.

View attachment 104243

 

[RoarinRow]

I'd be interested to see what people come up with..

 

[MLGrace]

Good question. I am also transitioning over now with a 5lb goal. Mine will be installed on my trailer. Hopefully some examples will be posted.

 

[trikebubble]

I have the AT Overland 10 pound tank holder mounted to the outside of my camper. They also make a 5 pound tank holder. It's pretty universal and you could easily sort out mounting it to pretty much anything.

 

[PCO6]

This won't help the OP but I mounted mine to the side of the box I installed on the tongue. I built a removable pedestal that I bolt to a piece of angle on the tongue under the box. The tank itself is held tight to the box with an 8" metal welding tank strap. On the other side I have a 10 litre water tank that is mounted using a similar insert. I abandoned the foam rubber hose shown in the second pic as it did not allow water to drain properly. I cut some small rubber pads to buffer the tank from the strap and they work fine.

View attachment 104454View attachment 104455

 

[utspoolup]

I have the power tank 5lb mount on my roof rack. Sadly the mounts cost as much as the bracket, which cost more than the tank, which is borderline nuts... just FYI. There is no real other option on my Xterra, since there is not a large aftermarket community for them like you Jeep.

 

[PNWDriver]

I have the power tank 5lb mount on my roof rack. Sadly the mounts cost as much as the bracket, which cost more than the tank, which is borderline nuts... just FYI. There is no real other option on my Xterra, since there is not a large aftermarket community for them like you Jeep.

Where’d you get that bracket from or did you make it?

 

[diabetiktaco]

This was at a meetup, only pic I got. But it's the frontrunner mount.

View attachment 178541

 

[PCO6]

I recently built a propane tank mount for my Jeep LJ tailgate. I fabricated the parts and bolted the mount to my MorRyde hinges which are designed to accept brackets. The tank actually bolts to the flat plate. It sits on a 1/8" thick rubber sheet and there are small holes in the plate for drainage. It's very solid; I can grab the tank and rock the Jeep. The only thing I have to do is add a bottle opener under the tank.

View attachment 178562View attachment 178563View attachment 178564

 

[rsweet]

17 lb Viking composite (half the weight of steel) cylinder on a Power tank mount mounted to Leitner ACS


View attachment 178566

 

[Tom Cole]

I attached mine to my rear swing-out. It makes it convenient to access for cooking. I'm not a sticker kind of guy, at least not on my vehicle. But I did decide to place a few on my propane bottle.

 

[MegaBug]

I wanted one for my backup 10lb tank. Ended up getting another one from Off Grid Trailers (where the trailer was built) so I could easily switch between the two tanks. I believe they make these themselves. I mounted it to the side of the trailer with rivnuts (as they did the original), but also positioned it so the weight would be fully supported by the running board, which can carry 400 lbs.
View attachment 178578

 

[genocache]

Probably won't help the OP much, but might give ya ideas. I built one for a 5# tank on my Land Rover.
CheckView attachment 178585 my blog for the full story;

Land Rover 109 propane tank mount

20 May 2020 Well you knew it was coming, right? If I went ahead and converted the white gas stove I'd have to get a tank or deal with all ...

poppageno.blogspot.com

Propane tank mount for 109, page 2

OK that was weird. Sorry out of my control. When we last left out intrepid hero fabricator it was late afternoon on 21 May 2020 he was in ...

poppageno.blogspot.com

 

[RoarinRow]

I came up with this.

View attachment 178597

View attachment 178598

I used a left over ditch mount bracket to attached the propane tank to the hitch carrier.

 

[genocache]

I came up with this.

View attachment 178597

View attachment 178598

I used a left over ditch mount bracket to attached the propane tank to the hitch carrier.

What's a "ditch mount"? Never mind I gooooooooooooooooooooooooooooooogled it.

 

[RoarinRow]

What's a "ditch mount"? Never mind I gooooooooooooooooooooooooooooooogled it.

I meant to say ditch mount extension. I ended up not using it to attach my CB antenna. So it worked out to hold the propane tank mount.

 

[PCO6]

Here's one I made for one of my trailers. It's constructed very much like the one for my Jeep LJ above (post #9).

View attachment 178605View attachment 178606

 

[MLGrace]

Put this on my expo trailer

 

[syrtus]

I initially made the mistake of mounting the propane tank on its side which caused the the heater and stove I was using to sputter and go out frequently. View attachment 178771

 

[PonoAdventures]

I came up with this.

View attachment 178597

View attachment 178598

I used a left over ditch mount bracket to attached the propane tank to the hitch carrier.

What size tank do you have? You used just one CBI antenna bracket? I have the same tire carrier and this may be a solution for me.