I have heard mixed opinions on to, or not to rotate your spare on the rig. Whats everyone else think?
Do you rotate you Spare on your rigs?
- Thread starter Pull the Pin
- Start date
Influencer II
- 4,645
- First Name
- Drew
- Last Name
- Sherwood
- Member #
-
6240
- Ham/GMRS Callsign
- KV50
- Service Branch
- Kern Valley SAR
Yes sir! and here is the proper 5 tire pattern!
View attachment 37604
View attachment 37604
Traveler III
Creator III
- 4,572
- First Name
- Rubi
- Last Name
- cajon
- Member #
-
8182
- Ham/GMRS Callsign
- KG5VLS
- Service Branch
- Navy Seabee’s
I agree with bandit. Proper rotation IMO helps with tread wear and prolongs tire life. Also include proper tire pressure.
Last edited:
Benefactor
Nope, I didn’t when I had a jeep with a matching spare now that I have a steel spare that doesn’t match the alloy wheels I definitely won’t. I actually probably only rotate the 4 on the truck half as often as recommended anyway. They seem to wear evenly enough for me and I have never noticed a big enough difference to matter. It’s the only maintenance that I’m not meticulous about. I could probably stretch a set of tires a little longer, and if it was a street vehicle I would do it more, but by the time it gets that close I am wanting deeper lugs again anyway so they tend to get replaced earlier than later. I have seen vehicles that wear tires dramatically though and rotation often is definitely needed. Fortunately for me this hasn’t been the case.
Sent from my iPhone using OB Talk
Sent from my iPhone using OB Talk
I do...with 2 spares.
I move the 2 rears to the front.
The 2 spares go on the rear.
And the 2 fronts become the spares
I move the 2 rears to the front.
The 2 spares go on the rear.
And the 2 fronts become the spares
Traveler III
- 4,007
- First Name
- Lucas
- Last Name
- Antes
- Member #
-
7082
- Ham/GMRS Callsign
- KE0ZXA
If I had a matching spare tire I would, but it's just a free all-season I got when the old spare tire would no longer hold air. Thankfully I do have a matching rim to the alloys on the rig. This is definitely something many do not practice due to most spares being a steelie or a donut. OB/off-road rigs might have better luck as they usually have a matching spare wheel
Enthusiast III
I do a five-tire rotation because I have a matching spare and want to make sure that, if and when I have to use it, the wear pattern roughly matches those of the remaining three tires.
Mixing a spare with fresh rubber with tires that have substantial wear risks the issue of compromised traction and handling, which I'd rather avoid at both highway speed and off-road. This issue is due in part to the difference in tread wear, and in part because a new tire will still have its coating of mold-release lubricant on it from the manufacturer's curing process. It takes roughly 500 miles of break-in before a new tire's coating is worn off and it performs at full design spec. In other words, a fresh spare will usually have inferior traction to the three broken-in tires. Having a spare with fresh rubber is better than having no spare at all, but a five-tire rotation avoids this issue and isn't any more difficult than a four-tire rotation.
Mixing a spare with fresh rubber with tires that have substantial wear risks the issue of compromised traction and handling, which I'd rather avoid at both highway speed and off-road. This issue is due in part to the difference in tread wear, and in part because a new tire will still have its coating of mold-release lubricant on it from the manufacturer's curing process. It takes roughly 500 miles of break-in before a new tire's coating is worn off and it performs at full design spec. In other words, a fresh spare will usually have inferior traction to the three broken-in tires. Having a spare with fresh rubber is better than having no spare at all, but a five-tire rotation avoids this issue and isn't any more difficult than a four-tire rotation.
